Local gas fireplace installation for Crawford homes

Direct-vent or B-vent, an installation in Crawford starts with a free visit to see where the vent can exit and what it has to clear.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local gas fireplace experts for new installs in Crawford

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Every clearance comes from the unit's manual, from the header height to the mantel depth.

Family owned and operatedOne family business frames, vents and starts up the unit in Crawford, and lines up the gas and electrical trades.
Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.

Call (904) 920-5495 Free Inspection

Gas fireplaces in bedrooms

The fuel gas code lists bedrooms among the rooms where gas appliances are not allowed, then writes exceptions that cover fireplaces. A direct-vent unit qualifies when it is installed to its listing, since it takes no air from the room. A B-vent unit qualifies only in a room big enough for the code's volume test, which compares the room's cubic footage with the unit's input. For a bedroom in Crawford, we measure the room, take the input from the unit's specifications, and put the arithmetic on the estimate so you can see whether a B-vent model passes or a direct-vent unit is the answer. Ring (904) 920-5495 with the room you have in mind, and our gas fireplace pros will plan the Crawford install on a free visit.

Crawford lies within Nassau County. Crawford is inland.

What a gas fireplace installation covers in Crawford

Heater or decorative listing matched to your plan
Vent route drawn and checked against the vent table
Start-up readings and leak check at the valve
Permit and inspections for your Crawford install scheduled

Call (904) 920-5495 Free Inspection

From vent exit to first burn in Crawford

Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.

Wall openings in Crawford in the storm months

Hurricane season lasts from June through November. A new opening through the wall or roof has to be weathertight before any storm arrives.

Exterior work on installs in Crawford is timed to the forecast, and the opening is covered until the termination is sealed.

10% off any service booked within 72 hours of inspection

Want a gas fireplace? Book within 72 hours of the planning visit and 10% comes off.

Call (904) 920-5495 Free Inspection

Restrictor settings on tall runs

A direct-vent run with a lot of vertical rise draws harder than a short one, and too much draft pulls the flame around and can lift it. Manuals handle this with a restrictor, a plate or adjustable damper in the exhaust path, set according to the vent configuration. The table in the manual gives the setting for each combination of rise and run.

We set it during installation and confirm it at start-up by watching the flame after the unit has warmed, adjusting only within the settings the manual lists. A flame that dances or lifts after warm-up is the sign it needs another look.

Sizing the supply to the input

Full rated input, at the pressure on the rating plate, is what the burner needs, measured at the valve with the burner running. The supply line from the meter or tank has to deliver that while the water heater, range and any furnace run too. Sizing that line is the gas contractor's job, done to the fuel gas code's tables, and it may mean a larger line or a new branch rather than a tap off the nearest pipe.

At start-up the inlet reading tells whether the supply did its job. A low inlet reading at start-up goes back to the gas contractor instead of into an adjustment at the valve.

No shortcuts through an old flue

An existing chimney or flue in the wall can look like a free vent path, but a vented gas fireplace uses the vent system its manual lists, run from the unit to its own termination. A vent tied into a wood-burning chimney, or shared with a water heater or furnace, is outside what the manuals permit.

Where an old chimney is to carry a gas vent, that is an insert or liner job with its own listed parts. The new vent route is drawn in full, from the unit to its own termination. That keeps each appliance's draft and exhaust separate. No existing flue is borrowed.

Unit, vent route and trades on paper

Termination spot measured to windows, soffits, corners and walks
Wall thimble or roof parts from the vent maker's list
Noncombustible facing and mantel height checked against the charts
Every connection leak-checked with solution before handover

Gas fireplace install questions from Crawford

Do you run the gas line to the new fireplace?

No. The line to the unit's shutoff valve is a gas contractor's job, or the propane supplier's on a propane system. The estimate says who and when, and start-up follows once gas reaches the valve.

Is a permit needed for a gas fireplace?

Yes. The permit comes from the local building department, and its inspections cover the gas connection, the vent and the framing before the finish closes them in. Both appear on the estimate.