Local fireplace insert installation in Brooklyn
A wood stove insert in Brooklyn connected to a stainless liner sized to its collar, with the damper locked open or removed.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Insert specialists who measure first in Brooklyn
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
The liner runs full length and matches the insert collar, the setup insert makers call the safest.
- Free inspection and estimateYour Brooklyn firebox, chimney height and hearth are measured against the insert's manual at no charge, before anything is ordered.
- Upfront pricing, no hidden feesEvery part of the job is priced before ordering, from repairs to the rain cap, and nothing is added without your yes.
- 100% satisfaction guaranteedIf the insert smokes or draws poorly after installation to its manual, we come back and set it right.
An insert with no pipe up the flue
Some older inserts were pushed into a fireplace and left to vent into the open smoke chamber, with nothing connecting them to the flue above. Current manuals expect more, a stainless pipe to the top or at least a sealed connection into the first section of flue lining, and the difference shows in how the unit drafts and how it is cleaned.
We check which setup you have by removing the surround and looking up past the insert, then write down what it would take to connect it properly. Unsure how the insert in your Brooklyn house was installed? Book a free check at (904) 920-5495.
Brooklyn sits in Duval County. Brooklyn is inland.
Liner, surround, clearances and hearth
- Firebox measured against the insert's size table
- Full-length stainless liners sized to the collar
- Top plates and rain caps closing the old flue
- Dampers locked open or removed for the liner
From tape measure to first fire in Brooklyn
-
Measure against the manual
Firebox, chimney height, hearth and clearances are checked against the insert's table before ordering.
-
Repair and clean first
Fireplace repairs are made and cured, and the flue is cleaned before the liner goes up.
-
Liner, plate and cap
A listed stainless liner runs to the top, closed with a top plate and a rain cap.
-
Set, seal and fire
The insert and surround go in as the manual directs, and the first fire is run with you.
Factory-built fireplaces inland in Brooklyn
A metal fireplace in Brooklyn can take an insert only where both manuals allow it. The rating plate tells us the model to look up.
We read both manuals before saying yes.
10% off any service booked within 72 hours of inspection
Insert measured through us in Brooklyn? Book it inside three days and 10% comes off.
A flue for the insert alone
Each wood insert needs its own flue. One insert maker states plainly that the unit must not be connected to a chimney flue serving another appliance, since two appliances on one flue can push smoke or exhaust into each other.
When a chimney holds more than one flue, we trace each one to see what it serves before choosing the path for the liner. If the one available flue is already shared, the insert waits until that is resolved, and the estimate says what it would take to free a flue for the insert. Nothing is connected until the route is clear.
Clearances measured from the insert body
Labels on inserts list how far combustible materials must stay from them. One model's figures, measured from the insert body, are 20 1/2 inches to an adjacent side wall, 24 inches to a mantel or top facing, and 6 1/2 inches to side facing that projects an inch and a half.
Other models have other numbers, so the label of your insert decides. We measure your mantel, trim, side walls and any shelves near the opening against those figures before ordering, and write down any trim that would have to change or any model it would rule out.
Reading the draft of a new insert
Draft is the pull that moves air into the insert and smoke up the chimney. One maker describes both ends of the range: too much draft can overheat the heater, shown by an uncontrollable burn or a glowing red part, while too little causes backpuffing and smoke leaking from joints.
After installation we watch the first burn for either sign. A liner sized to the collar and a chimney at the manual's height put the draft in range in the ordinary case, and where they do not, we say what to adjust before the insert is used hard. Any change we make is written on the ticket.
Fireplace, flue and hearth on paper first
- Fireplace cracks, loose mortar and throat condition repaired before install
- Mantel, side facing and side wall clearances measured to the label
- Blower outlet location, with any new circuit named for an electrician
- Metal tag fixed to the fireplace back wall when the manual supplies one
Wood insert questions from Brooklyn
Do I need a full liner for an insert?
Insert manuals allow a full liner or, where they permit it, a short positive connection. The full liner drafts better and is easier to clean, and it is what we recommend and price first.
Does a new wood insert have to meet an EPA limit?
New wood heaters made or sold at retail since May 15, 2020 must meet the EPA Step 2 limit, and the permanent label says so. We read it before installing.
More services in Brooklyn
-
-
-
-
-
-
Learn more about wood-burning fireplace insert installationAll services in Brooklyn
Turn your Brooklyn fireplace into a heater
Have the insert model handy when you ring (904) 920-5495, and our fireplace experts will check it against your Brooklyn firebox.
Free Inspection