Local chimney rebuild in Brentwood
A free inspection tells you if the problem starts at the footing before we price rebuilding the top of your Brentwood chimney.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local rebuild experts for Brentwood chimneys
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
The finished chimney in Brentwood is measured against the code's height rule before the crown is cast.
- Family owned and operatedOur family business takes your Brentwood chimney down by hand and lays it back up itself.
- Upfront pricing, no hidden feesThe take-down line, flue plan and crown are priced before the first brick comes off.
- Workmanship warrantyFrom the new courses to the counterflashing, the rebuilt stack carries our workmanship warranty.
After a limb or debris strike
An impact from a falling limb or wind-driven debris can knock courses out of line, crack the crown and bend the cap, and the damage can reach lower than it looks. Courses below the visible break get the same hand and tool tests as the rest, because a blow can loosen joints several courses down.
The flue is checked for tile knocked into the passage, and the fireplace stays unused until it has been. Impact damage on the Brentwood chimney is kept apart from older wear, with each item described in plain words. Chimney leaning or dropping brick in Brentwood? Ring (904) 920-5495 for a free rebuild assessment.
Within Jacksonville city limits, Brentwood is its own named neighborhood. Brentwood is part of Duval County.
Rebuild work around Brentwood
- Flue covered before the first brick comes off
- Sound original brick cleaned and saved to relay
- Mortar type chosen from ASTM C270 for the exposure
- Flue tile set in refractory mortar or a listed liner run
How our rebuild specialists work in Brentwood
-
Courses tested, line marked
Each course is pressed and probed from the top down, and the take-down line is marked where sound brick starts.
-
Taken down under cover
The flue is plugged and the roof protected, then brick comes off by hand and sound units are saved.
-
Relaid with flue and flashing
Courses go back plumb in the chosen mortar, the flue tile or liner rises with them, and counterflashing is set into the joints.
-
Height, crown and cap
The height is checked, a crown is cast with a drip edge and bond break, and the cap goes on after it cures.
Flue work inside a rebuild in Brentwood
A rebuild opens the flue, which makes it the right time to fix a cracked tile run or plan a liner. New clay tile is set in refractory mortar as the courses rise.
When a listed stainless liner suits your Brentwood chimney better, the rebuild leaves room for it.
10% off any service booked within 72 hours of inspection
Loose or leaning chimney? Book the rebuild up to 72 hours after we inspect and save 10%.
How thick the chimney walls must be
A rebuilt chimney has to meet the code's wall thickness. Masonry chimney walls are built of solid masonry units, or hollow units with their cores grouted solid, not less than 4 inches in nominal thickness (FBC R1003.10).
That works out to one full brick thickness around the flue, with the tile or liner space inside it. A rebuild does not thin the walls to fit a larger liner, and where an old stack was built thinner than that, the rebuilt section is brought up to the requirement. Corners are interlocked course by course so the walls act together.
Where new flue tile starts and how far it may lean
The code sets where clay tile begins. For a flue serving an appliance, it starts no less than 8 inches under the lowest inlet; for a fireplace, it starts at the top of the smoke chamber, and it runs to a point above the enclosing walls (FBC R1003.12).
The tile runs vertically where it can, and where it must offset, the slope stays within 30 degrees of vertical. A rebuild that goes low enough to reach the smoke chamber rebuilds that starting point too, and you know in advance how far down the new tile begins. The first tile sits on a solid base, clear of loose rubble.
A cricket behind a wide chimney
On the uphill side of a chimney, water running down the roof piles against the masonry. A narrow chimney splits the flow on its own; a wide one needs help. The code requires a cricket, a small ridged diverter, where the chimney measures more than 30 inches parallel to the ridge and does not meet the ridge (FBC R1003.20).
Changing the chimney's width or position during a rebuild is the time to check that requirement. The cricket ties into the roof covering, so its builder and its junction with the new flashing are settled before work starts.
Tested before a rebuild is priced in Brentwood
- Take-down line stated in courses or feet, with the reason for it
- New clay tile in refractory mortar, or space left for a listed liner
- Masonry divider rebuilt between flues where two share the stack
- Cast crown with an overhang, a drip edge and a sealed bond break
Before the first brick comes off
Will a roofer be involved in the rebuild?
Sometimes. The rebuild includes counterflashing set into the new joints, but base flashing woven into the roofing, a cricket, or roofing repairs may need a roofer; each is assigned on the estimate.
Can the chimney be made taller during the rebuild?
Yes, when the code's height rule calls for it. The added courses are laid before the crown, and the flue tile or liner is lengthened to match.
More services in Brentwood
-
-
-
-
-
-
Sound brick up to a new crown in Brentwood
Brick on the roof in Brentwood? Keep clear of the area below, and our specialist checks the top at no charge.
Free Inspection