Local chimney waterproofing for Atlantic Beach homes
Product chosen on a free inspection, cure times kept, glass protected. That is chimney waterproofing in Atlantic Beach.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Waterproofing specialists who test Atlantic Beach brick first
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Film sealers and paint trap water in brick, which is why they stay off the chimneys we treat.
- Free inspection and estimateWe splash test your Atlantic Beach chimney at no charge and tell you if the brick needs treatment at all.
- No hidden feesRepairs and repellent are separate lines, and nothing is added once the spraying starts.
- 100% satisfaction guaranteedIf treated brick still soaks up water where we sprayed, we come back and put it right.
Waterproofing or leak repair?
A leak into a room and brick that soaks up rain are related but different problems. A leak has an opening behind it, somewhere water can run in: a crack, a gap at the flashing, a failed crown. Soaking a repellent into the faces of the brick does nothing to close such an opening, since the product lines the pores rather than filling gaps.
When water is showing inside your Atlantic Beach home, the leak is traced and repaired first, and its entry point is named. Treating the brick is a separate question that comes afterward, once the stains stop spreading. Which faces stay damp after rain in Atlantic Beach? Let us know at (904) 920-5495, and we start there.
Atlantic Beach reaches the coastline. Atlantic Beach is in Duval County.
Waterproofing work we do in Atlantic Beach
- Brick cleaned so the repellent reaches the pores
- Test patch left to dry beside untreated brick
- Flood coat applied from the bottom up
- Coverage kept to the maker's rate, never heavier
How chimney waterproofing runs
-
Splash test every face
Water on each face shows where the brick soaks it up, and the crown, cap and flashing are checked for openings.
-
Openings closed and cured
Joints, brick, crown and flashing are repaired first, and the cure time on the data sheet runs its course.
-
Clean, patch test, then flood
The brick is cleaned, a test patch dries beside untreated brick, then the repellent goes on from the bottom up.
-
Dry and retest
Once it has cured, we splash the faces again so you can see the water bead off.
Why film sealers fail on coastal chimneys
A shiny sealer can look like good protection against salt spray, but it traps the water already in the brick. On chimneys near the ocean that water keeps coming, and the film blisters and peels.
In Atlantic Beach we remove failing films where the product maker says it is needed and use a breathable penetrating repellent instead.
10% off any service booked within 72 hours of inspection
The repairs that come first and the water repellent after them are both discounted.
How a film sealer holds water in brick
Clear products that sit on top of the brick, such as acrylics, stearates, waxes and urethanes, dry into a continuous skin. The skin can span a hairline crack, which sounds like an advantage, but it also chokes the vapor that has to leave the wall when it dries. On a chimney, water arrives from above, from the flue side and through joints as well as through the faces.
If that water cannot escape outward at its normal pace, it stays in the brick longer, and BIA warns that salts can collect under such a skin and harm the face. For that reason we do not use film sealers on chimney masonry.
Painted or glazed brick is left out
The maker's directions for the repellent we apply exclude painted brick and glazed brick or tile. Paint already forms a film on the face, and a glazed unit has a fired, glass-like surface that the product cannot enter. Spraying either one wastes material and can leave a haze. Painted or glazed sections of a chimney are therefore masked off and left untreated. If paint on the chimney is blistering, peeling or taking the brick face with it, that points to moisture trapped behind it, and what to do about the paint is set out as a separate decision.
The splash test for when to reapply
You can check whether a chimney's treatment is still working without any tools beyond a spray bottle or a garden hose on a gentle setting. Wet a patch of each face. Brick that is still protected throws the water off in beads and keeps its dry color; brick that has lost its protection turns darker within seconds as it soaks the water up.
We run that test on every face, since the face that takes the most weather wears first. Only faces that absorb get another coat, which saves product and avoids stacking coats where they are not needed. The results, face by face, go into the job notes.
Tested before any repellent goes on in Atlantic Beach
- Product name and type: silane, siloxane or a blend of the two
- Weather window: dry masonry, no rain forecast, temperature in range
- Existing sealer or paint identified before any product is chosen
- Clean-up of overspray on nearby surfaces the same day
Before any sealer goes on
Can the treatment be done the same day as repointing?
No. Fresh joints need at least 72 hours to cure first, according to BIA and the product's data sheet, so treatment is a second visit.
Can you treat a stucco chimney?
The product we use lists portland cement stucco among its surfaces. Cracks in the stucco are repaired first, and a test patch shows how it takes the product.
More services in Atlantic Beach
-
-
-
-
-
-
Learn more about chimney waterproofingAll services in Atlantic Beach
Find out if your Atlantic Beach brick needs sealing
Family-owned masonry professionals check whether your brick in Atlantic Beach needs treatment at all. The test is free.
Free Inspection