Direct vent and B-vent service for American Beach gas fireplaces

The code's clearances and the maker's vent rules, applied to your American Beach gas fireplace on a free visit.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local vent specialists who repair with listed parts

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Cap distances are taped against the code table and the maker's drawing.

Free inspection and estimateThe vent on your American Beach gas fireplace is traced from the collar to the cap and measured against the code at no charge.
Upfront pricing, no hidden feesEach section, fitting and reroute is priced on its own line before any pipe is cut or replaced.
100% satisfaction guaranteedIf the flame, the draft or the shutdown problem is not fixed by the vent repair we quoted, we come back.

Call (904) 920-5495 Free Inspection

Direct vent or B-vent

Gas fireplaces vent in one of two ways, and knowing which one you have decides every repair. Sealed direct-vent units breathe through a pipe-within-a-pipe to the outside, while natural-vent units pull air from the room and push exhaust up a double-wall pipe on its own heat. The rating plate and the pipe itself usually settle the question in minutes.

The two systems use different parts and follow different rules, and a repair keeps the one the appliance was built for. Not sure which kind is on your American Beach fireplace? We identify it free; call (904) 920-5495.

American Beach is part of Nassau County. American Beach borders the coast.

What gas fireplace venting covers in American Beach

Blocked terminations cleared after storms
B-vent caps raised to the roof pitch table
Spillage tested with the house's fans running
New vent routes drawn before any cutting

Call (904) 920-5495 Free Inspection

How our venting pros trace a gas vent in American Beach

Identify the system
The manual and pipe markings tell us the vent type, size and maker.
Trace the run
With the unit off and cool, we follow the vent and check joints, supports and clearances.
Repair with listed parts
Joints are reseated, damaged sections replaced and crowded caps moved.
Test and record
We fire the unit, check flame and draft, then note every fix.

Roof caps on coastal homes in American Beach

B-vent caps on coastal roofs in American Beach take wind and salt together. A cap loosened by wind or eaten by rust drafts poorly.

We check its height, fastening and condition from the roof.

10% off any service booked within 72 hours of inspection

Comparing vent quotes? 72 hours gives you time to weigh ours and still save 10%.

Call (904) 920-5495 Free Inspection

A cap under a deck or porch

Under a veranda, porch, deck or balcony, a direct-vent cap is allowed only with conditions. One maker allows it at 12 inches of clearance, and only when the space is fully open on at least two sides beneath the floor.

Enclosing the sides of a deck later can turn a legal cap into a problem, because exhaust has nowhere to go. We check how open the space is today and, where it has been closed in, reroute the vent or open the sides. The same chart keeps the cap from terminating directly above a sidewalk or driveway shared by two homes. Lattice added under a deck counts as closing it in.

Air space around the pipe

Hot pipe needs air around it, and its maker sets that space to combustibles. One manual requires 3 inches above horizontal runs and 1 inch at the sides and bottom until the pipe passes the outside wall, and 1 inch all around at the wall and on vertical runs.

The same manual warns against packing those spaces with insulation or other materials, since that can cause high temperatures and a fire hazard. We check spacing where the pipe crosses joists, studs and the wall thimble, and clear anything crammed into the gap. Firestops and thimbles are made to hold that spacing, which is why they matter.

Where the vent work stops and the roof begins

A roof penetration for a gas vent involves two trades. The vent, its storm collar and its cap are ours to fit to the maker's instructions; the shingles, underlayment and roof covering around the penetration belong to a roofer.

When a vent has leaked at the roof, we find whether the water came through the vent parts or the roof covering, and write up each for the right trade. That keeps a vent repair from being blamed for a roof problem, or the other way round, and the estimate says plainly who does what. Both trades can work the same week so the roof is not left open.

Traced in American Beach before any vent pipe is replaced

Every reachable joint checked for full engagement and its lock
Termination measured against Table 503.8 and the maker's chart
Supports, firestops and fastening along the run
Flame watched on a test run after every repair

Before the vent is opened up

Is B-vent the same as direct vent?

No. B-vent carries exhaust up by natural draft from a unit that burns room air; direct vent is sealed and draws its air from outside. Each fireplace uses the one it was built for.

Can I use another brand's pipe on my direct-vent fireplace?

Not unless the manual lists it. Direct-vent pipe is tested as part of the appliance, so sections come from the listed system.