Gas insert fireplace installation in Sunbeam
Upfront pricing for a gas insert in Sunbeam once a free inspection has measured the fireplace.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Gas insert pros who measure first in Sunbeam
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
The ticket records the model, the vent kit and the liner sizes for later service.
- Free inspection and estimateThe opening, flue and mantel of your Sunbeam fireplace are measured against the insert's plate at no charge.
- Upfront pricing, no hidden feesInsert, vent kit, surround, cleaning and repairs are priced line by line, and the gas and power trades are named.
- 100% satisfaction guaranteedIf the insert does not light, burn or seal the way its manual describes after our installation, we come back.
A carbon monoxide alarm near the insert
Carbon monoxide comes with burning gas, and a sealed insert is built to send all of it outside. An alarm in the room still makes sense as a backstop, and one insert maker suggests one alongside yearly service. Headaches, dizziness or nausea while the insert runs mean everyone leaves the house and 911 gets the call from the driveway.
We suggest a spot for the alarm on install day, and every later service visit checks the vent and the seal. Adding a gas insert to a home in Sunbeam with no CO alarm near the fireplace? Mention it when you book at (904) 920-5495.
Sunbeam is part of Duval County. Sunbeam is an inland community.
Liners, surround, gas and power
- Co-linear liners run to a listed termination
- Co-axial and adapter kits where the manual calls for them
- Barrier screens and relief doors checked
- Yearly service set up from the first day
How gas insert installation runs
-
Measure against the plate
Opening, flue and mantel are checked against the insert's rating plate and manual.
-
Clean and check the chimney
The old flue is cleaned, examined and repaired if needed before the liners go up.
-
Liners, insert, surround
The vent kit runs to its termination, the insert is set and the surround fitted.
-
Hookups and first light
The gas and electrical hookups are made, then we light and test the insert with you.
CO alarms and inserts in Sunbeam
A new gas insert in Sunbeam is a good reason to put a carbon monoxide detector in the same room.
We point out a sensible spot.
10% off any service booked within 72 hours of inspection
Switching to gas? Book the insert within 72 hours of the inspection and take 10% off.
Mantel clearance above a gas insert
Heat rising from a gas insert reaches the wall and anything fixed to it. One maker's rating plate lists 12 inches from the top of the appliance, as the plate words it, to the underside of a combustible mantel that projects up to 3 inches, and refers to its installation manual for deeper mantels.
Deeper mantels need more height, following a chart in the manual. We measure your mantel's height and projection against the figures for your model before ordering, and a mantel that falls short means a different model, a raised mantel or a noncombustible one. The choice is made on paper first.
Gas pressure at the valve
Every gas insert's rating plate lists the supply pressures its valve needs. One maker's plate gives a minimum of 4.5 and a maximum of 7 inches of water column for natural gas, and 11 to 13 for propane, with manifold pressures set lower.
The gas contractor or propane supplier sizes the piping to deliver that range, and once the supply is at the valve, we connect the insert, leak test every joint we made and read the pressures at the valve's test ports with the burner running. The readings go on the ticket. Pressures outside the plate's range are corrected before the insert runs for any length of time.
Only the fronts made for the insert
Decorative fronts and doors for gas inserts are sold separately, and not all of them fit every model. One maker's manual allows only the doors and optional fronts approved with the unit to be installed on it.
A front from another model can block air openings, change how the glass seals or overheat, even if it looks like it fits. We order fronts from the parts list for the insert's model, and when a customer already has a front, we check its part number against that list before it goes on. The part numbers on the front and the plate should agree.
Measured in Sunbeam before a gas insert is ordered
- Vertical height and offsets measured against the vent limits
- Liner bend radius kept through the throat and smoke shelf
- Surround sized to the face, with noncombustible finishes around it
- Outlet position behind the surround, wired by an electrician where needed
Before you switch to gas
Who runs the gas line?
The gas trade does: a gas contractor, the gas company or your propane supplier. Their part is on the estimate with a date, and our hookup follows once gas reaches the valve.
Can I keep my mantel?
Yes, when its height suits its depth under the insert's figures. Otherwise the choice is another model, a higher mantel or a noncombustible one, settled before ordering.
More services in Sunbeam
-
-
-
-
-
-
Learn more about gas fireplace insert installationAll services in Sunbeam
Book a gas insert check in Sunbeam
Have the insert model ready when you ring (904) 920-5495, and our experts check it against your Sunbeam fireplace.
Free Inspection