Family-run chimney tuckpointing in Ponte Vedra Beach

Repointing at your Ponte Vedra Beach home comes 10% off when you book it inside three days of the survey.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local repointing pros for Ponte Vedra Beach chimneys

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

The color is matched from a cured test batch before a single joint is filled.

Free inspection and estimateEvery face of your Ponte Vedra Beach chimney is scratch-tested and sketched at no charge.
100% satisfaction guaranteedIf the new joints are not sound, full and matched as agreed, we come back and fix them.
Family owned and operatedA family masonry crew does the survey and the work, so the person who priced a face is the one who repoints it.

Call (904) 920-5495 Free Inspection

Joints that open after a storm

Heavy wind and rain do not usually strip sound mortar, but they can finish off joints that were already weak. After a storm, loose mortar crumbs on the roof or a fresh gap in a joint are worth checking. Nothing on the sketch is priced by guesswork, since each face was checked at arm's length.

We look for the joints that failed and the ones about to, since weak mortar rarely fails alone. Repointing them before the next storm keeps water out of the brick. Mortar gone from your Ponte Vedra Beach chimney after bad weather? Phone (904) 920-5495; our masons inspect it for free.

Ponte Vedra Beach sits in St. Johns County. Ponte Vedra Beach lies on the coastline.

Raked, filled, tooled and cured

Every face scratch-tested and sketched
Joints cleaned and dampened before filling
Old caulk and skim patches cut out
A repointing sketch of your Ponte Vedra Beach chimney, free

Call (904) 920-5495 Free Inspection

From the scratch test to cured joints in Ponte Vedra Beach

Every face surveyed
Joints are scratch-tested at several heights and the failed courses marked on a sketch.
Joints raked and cleaned
Old mortar comes out to sound depth, head joints by hand, then joints are cleaned and dampened.
Filled in layers and tooled
Matched mortar goes in stage by stage, then is tooled to the original profile.
Cured and cleaned up
Fresh joints are protected while they cure, the faces brushed and the roof cleared.

Salt on the brick and joints in Ponte Vedra Beach

Salt carried on the ocean wind settles on chimneys along the coast, and water moving through the masonry carries salts to the surface as it dries.

When we find white deposits on a chimney in Ponte Vedra Beach, we brush them back to see the joints beneath before deciding what to repoint.

10% off any service booked within 72 hours of inspection

Repointing earns the discount whether or not you have used our masons before.

Call (904) 920-5495 Free Inspection

How deep worn mortar is raked out

National Park Service Preservation Brief 2 ties raking depth to joint width. Take a joint 3/8 inch wide: its old mortar comes out at least 3/4 inch deep, roughly double its width or a little beyond, and deeper again where it is still loose. For typical brick joints, that lands around half an inch to an inch.

Too shallow, and the new mortar sits as a thin skin that falls out. Too deep without cause, and bricks lose support. We rake to sound mortar, square the back of the joint so the new fill has a flat surface to bond against, and check depth as we go rather than trusting one measurement.

Tooling the joint to shed water

Once the final layer has firmed, the joint is tooled: pressed and shaped with a jointer to compact the surface and match the profile of the old joints. Tooling closes tiny gaps at the brick edge where water could enter.

For exterior walls, the Brick Industry Association's water penetration note prefers concave and V profiles made with a jointer, since tooling compacts the mortar and the shape sheds rain. Where the original joints are a different profile, we match them so the wall reads as one. The profile used is written on the estimate. A joint tooled too early smears, and one tooled too late crumbles at the edge, so timing is watched face by face.

Full joints against wind-driven rain

On chimneys close to the ocean, storm wind drives rain hard against the masonry, and any gap along a joint edge becomes a way in. Brick Industry Association guidance on water penetration stresses full mortar joints and tooled profiles for exactly that kind of exposure.

So near the coast we pay particular attention to filling joints completely, with no voids behind the face, and to tooling them tight against the brick. We also check the faces that take the most direct weather, since wind-driven rain wears their joints soonest. Joints on those faces are raked and refilled with extra care at the brick edges, where rain finds its way in first.

Joint findings written down before pricing

Color matched from a cured test batch shown to you first
Caulk or skim patches to remove before repointing
Days on site and the wait before the next fire
Joints that can wait a season, and how to watch them

Repointing questions from Ponte Vedra Beach

Could the cracks simply be caulked?

Caulk or a thin skim over worn mortar has nothing solid to grip and falls away, often hiding deeper failure while it lasts. Raking and refilling the joint is the repair that holds.

Is a fire safe while the chimney is being repointed?

Best not on the days we work on the top, and not until the new mortar has had its curing time. The estimate gives the wait based on the mortar and the weather.