Local gas fireplace installation for Lake Asbury homes

Local pros fit a vented gas fireplace to your Lake Asbury room, route the vent to the manual and name who brings the gas. Planning is free.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Gas fireplace install specialists for Lake Asbury

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Wiring for the blower and remote goes in before the wall is closed, so nothing gets cut open later.

Family owned and operatedOne family business frames, vents and starts up the unit in Lake Asbury, and lines up the gas and electrical trades.
Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.

Call (904) 920-5495 Free Inspection

Choosing the controls

How a gas fireplace lights and how you run it are part of the choice. A standing pilot with millivolt controls works without house power, and its pilot burns whenever the unit is on standby. Electronic ignition lights the pilot only when called, needs power or a battery backup, and pairs well with a remote or a thermostat. Some units offer both modes. We set out the options each candidate unit offers for your Lake Asbury room, including what it does in a power outage, so the controls you get match how you plan to use the fireplace. Want gas heat in Lake Asbury in a room with no chimney? We check the wall first, and it starts with a call to (904) 920-5495.

Census takers counted 11,036 people in Lake Asbury in 2020. Lake Asbury does not reach the coast.

From vent exit to first burn

Direct-vent or B-vent unit chosen for the room
Heater or decorative listing matched to your plan
Facing and mantel planned from the manual's chart
Walk-through of your new Lake Asbury unit and its manual

Call (904) 920-5495 Free Inspection

From vent exit to first burn in Lake Asbury

Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.

Wiring before the wall closes in Lake Asbury

Remote receivers, wall switches and blowers need wiring run before the finish goes on. Running it later means cutting into the new wall.

On installs in Lake Asbury, the electrician's rough-in is on the schedule before the drywall.

10% off any service booked within 72 hours of inspection

Direct-vent or natural-vent, the installation is discounted either way.

Call (904) 920-5495 Free Inspection

Framing the enclosure and the header

Framing starts from the manual's drawing, which gives the width, height and depth of the enclosure and the header height above the unit. The header matters because the space above a gas fireplace gets hot, and the manual sets how high framing can come. Some units have drywall support tabs on their face, and the manuals point out that those tabs are for holding the drywall edge and never for carrying framing or a header.

We build the enclosure to the drawing, square and plumb, so the unit sits where the clearances assume it does. A header set too low means reframing, so it is measured twice.

Facing materials and the heat they see

The metal face around the opening of a gas fireplace runs hot enough that the manual controls what goes over it. Only noncombustible finishes the manual accepts qualify, which rules out wood, paneling and ordinary drywall on that surface. Facing goes on with a high-temperature adhesive of the rating the manual names, and any joint sealed between the facing and the wall uses a high-temperature sealant. Wood trim and combustible board stay outside the zone the drawing marks.

Choosing a facing that meets those rules before it is bought avoids tearing it out after the inspection. Metal trim kits from the maker can frame it.

The first long burn

A new gas fireplace gives off an odor the first time it runs, as the paint and materials cure, so plan on open windows during that burn-off, as the manuals advise. One maker recommends running the unit for an extended period the first time, with the fan switched off. We start that process at handover, open the windows, and tell you what to expect over the first few fires.

An odor that persists after the burn-off, or any smell of gas, is a different matter and a reason to call. Children and pets are best kept out of the room while it happens.

Unit, vent route and trades on paper

Vent route drawn with each elbow counted against the vent table
Horizontal pitch and support spacing set as the manual shows
Noncombustible facing and mantel height checked against the charts
Barrier screen fitted and logs set to the placement diagram

Gas fireplace install questions from Lake Asbury

Can I choose the tile or stone around the fireplace?

Yes, within the manual's rules. Only noncombustible materials may cover the metal face, set with the adhesive rating the manual gives, and a mantel follows the manual's chart.

Is a permit needed for a gas fireplace?

Yes. The permit comes from the local building department, and its inspections cover the gas connection, the vent and the framing before the finish closes them in. Both appear on the estimate.