Local gas fireplace venting in Kings Ferry

Local experts repair gas fireplace vents in Kings Ferry, backed by our satisfaction guarantee.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Venting pros who trace the whole run in Kings Ferry

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Horizontal runs get a level on them, since slope matters to both vent types.

Free inspection and estimateThe vent on your Kings Ferry gas fireplace is traced from the collar to the cap and measured against the code at no charge.
Upfront pricing, no hidden feesEach section, fitting and reroute is priced on its own line before any pipe is cut or replaced.
100% satisfaction guaranteedIf the flame, the draft or the shutdown problem is not fixed by the vent repair we quoted, we come back.

Call (904) 920-5495 Free Inspection

A vent through a cold chase

Natural-draft vents depend on warm exhaust rising, and a chase that stays cold can slow that down until the fireplace spills or struggles. How the chase is built, and whether it is insulated, is part of the diagnosis. A chase that is warm in winter helps a natural-draft vent start drawing.

Insulation near the pipe still has to keep its distance, so the fix is planned, not improvised. B-vent fireplace in a chase at your Kings Ferry house? Ask about the draft at (904) 920-5495.

The county for Kings Ferry is Nassau County. Kings Ferry does not reach the coast.

Joints, caps, clearances and slope

Blocked terminations cleared after storms
Sagging runs resupported and resloped
Shared vents separated into one per appliance
Your Kings Ferry vent traced from collar to cap

Call (904) 920-5495 Free Inspection

From collar to cap in Kings Ferry

Identify the system
The manual and pipe markings tell us the vent type, size and maker.
Trace the run
With the unit off and cool, we follow the vent and check joints, supports and clearances.
Repair with listed parts
Joints are reseated, damaged sections replaced and crowded caps moved.
Test and record
We fire the unit, check flame and draft, then note every fix.

Attic B-vent runs inland

Attic runs of B-vent in Kings Ferry can sag, lose supports or have insulation pushed against them over the years.

We walk the run and check spacing and slope.

10% off any service booked within 72 hours of inspection

Cap too close to a window in Kings Ferry? The reroute is discounted too.

Call (904) 920-5495 Free Inspection

What Type B vent is

Type B gas vent is double-wall pipe for natural-draft gas appliances. Section 502.1 of Florida's fuel gas code requires Type B and BW gas vents to be listed and labeled and tested to UL 441, and the appliance's manual names the diameter.

One maker's B-vent fireplaces use a 4-inch vent on one model and a 6-inch vent on others. The inner and outer walls keep the hot exhaust away from framing, and the space between them is part of the design. Replacement sections match the listing and the diameter the manual calls for. Single-wall pipe is not a substitute anywhere a Type B vent is required.

The slope of a horizontal run

Horizontal vent sections have a direction. On one maker's B-vent units, a flat stretch must climb a quarter inch or more for every foot, with no level or falling sections, and its direct-vent sister manual lists a horizontal vent pitched wrong as a cause of the pilot and burner going out.

The same direct-vent manual has flexible horizontal runs rising an inch for every 24 inches from the unit, while its twist-lock rigid runs follow their own rule. We put a level on each horizontal section and rehang any that has settled or was hung wrong. A run that dips can hold condensate as well as exhaust.

How twist-lock joints are made

Much direct-vent pipe joins with a twist lock. One maker's manual has the beads on the male end aligned with the grooves of the female end and the pipe turned until the flange meets the outer pipe. Screws in the joint are optional on that system, and sealant is not required.

The same manual says not to use silicone at the inner flue. A joint turned only partway can look closed and still leak. We check each reachable joint for full engagement and replace a section whose bead or groove is damaged. Screws, where used, go only through the outer pipe.

Clearances, slope and caps on paper

Air space to framing checked where the pipe passes joists and walls
Termination measured against Table 503.8 and the maker's chart
Restrictor position checked against the manual
Damaged sections replaced from the listed vent system

Gas fireplace vent questions from Kings Ferry

Why does my flame look blue and lazy?

It is short of air, and a blocked vent is one of the listed causes. Turn the unit off and have the cap and joints checked.

Is the vent inspection free?

Yes. The trace and the written quote cost nothing, and the quoted price does not grow. Book the repair within 72 hours of the trace and you save 10% on it.