Gas fireplace installation in Fleming Island by local specialists

Unit, vent parts, termination spot and start-up checks for your Fleming Island install, all worked out on a free planning visit.

Fully licensed and insured
Locally owned
Family owned and operated
Same-day service

Call (904) 920-5495 Free Inspection

Get Your Free Inspection

Get a quote for chimney and fireplace repair and installation in Jacksonville.

Quicker by phone? Call (904) 920-5495

Call our chimney crew

(904) 920-5495 Free Inspection

Local gas fireplace experts for new installs in Fleming Island

Locally owned in Jacksonville
Family owned and operated
100% satisfaction guaranteed
Free inspection and estimate
Same-day service available
10% off any service

Wiring for the blower and remote goes in before the wall is closed, so nothing gets cut open later.

Family owned and operatedOne family business frames, vents and starts up the unit in Fleming Island, and lines up the gas and electrical trades.
Workmanship warrantyThe workmanship warranty applies to our venting, framing and start-up, and the unit keeps its maker's terms.

Call (904) 920-5495 Free Inspection

When a log set or an insert suits better

An existing wood-burning fireplace in a house in Fleming Island changes the question. A gas log set can go into a sound masonry firebox and vent through the existing chimney, and a sealed gas insert can slide into it with a vent run up the old chimney. Gas log installation and gas fireplace insert installation are separate jobs we also do.

Before recommending a new built-in unit, we look at the fireplace you already have, because using it can mean no new wall opening and no new termination. We tell you which of the three makes sense for the room, and why. On the free planning visit in Fleming Island we check where a vent can exit; call (904) 920-5495.

Fleming Island is on the St. Johns River. The county for Fleming Island is Clay County.

From vent exit to first burn

Heater or decorative listing matched to your plan
Siding standoff fitted behind a wall termination
Facing and mantel planned from the manual's chart
Gas line to the shutoff valve assigned to a gas contractor

Call (904) 920-5495 Free Inspection

Vent out, frame, wire, start up

Vent exit found first
We find where the vent can leave the house within the manual's clearances, then pick the unit to suit.
Frame and run the vent
The enclosure and header are framed to the drawing, and the vent is run with its supports, pitch and firestops.
Trades, wiring and gas
Wiring goes in before the wall closes, and the gas contractor brings the line to the shutoff valve.
Start-up and inspection
Pressures are read, joints leak checked, the inspector signs off, and we go over the controls with you.

Sizing the gas supply in Fleming Island

The burner needs its full rated input at the pressure on the rating plate. The supply line is sized for that, with the rest of the house running too.

The gas contractor sizes and runs the line in Fleming Island, and we check the pressure at start-up.

10% off any service booked within 72 hours of inspection

Direct-vent or natural-vent, the installation is discounted either way.

Call (904) 920-5495 Free Inspection

Pitching the horizontal runs

The manual says how a horizontal section of vent is pitched, and different systems ask for different things. One system may allow a level run while another asks for a set rise per foot away from the unit, so the figure comes from the manual in hand every time. The pitch decides how exhaust and any condensate move through the pipe. A section that sags or runs back toward the unit can upset the draft and, on some units, put the pilot out.

We set each section with a level and support it at the spacing the manual gives. Pitch is checked again after the wall is closed around it.

Facing materials and the heat they see

The metal face around the opening of a gas fireplace runs hot enough that the manual controls what goes over it. Only noncombustible finishes the manual accepts qualify, which rules out wood, paneling and ordinary drywall on that surface. Facing goes on with a high-temperature adhesive of the rating the manual names, and any joint sealed between the facing and the wall uses a high-temperature sealant. Wood trim and combustible board stay outside the zone the drawing marks.

Choosing a facing that meets those rules before it is bought avoids tearing it out after the inspection. Metal trim kits from the maker can frame it.

Propane tanks and the fireplace

A propane fireplace runs off a tank outside the house, and the manuals are explicit that propane tanks do not go inside any structure. Some manuals set a minimum tank size so the tank can vaporize enough gas to keep up with the unit, which matters on small tanks.

The regulator at the tank and the line to the house belong to the propane supplier. We confirm with the supplier that the tank, regulator and line suit the fireplace's input before the unit is ordered, so start-up is not the first time anyone checks. The supplier's answer is kept with the installation plan.

Unit, vent route and trades on paper

Framed opening and header height taken from the manual
Vent route drawn with each elbow counted against the vent table
Wall thimble or roof parts from the vent maker's list
Noncombustible facing and mantel height checked against the charts

Gas fireplace install questions from Fleming Island

Can a gas fireplace be installed in a house in Fleming Island without a chimney?

Yes. A direct-vent unit uses its own listed vent pipe through a wall or the roof, so no chimney is needed. The site visit checks where the termination can go.

Is a permit needed for a gas fireplace?

Yes. The permit comes from the local building department, and its inspections cover the gas connection, the vent and the framing before the finish closes them in. Both appear on the estimate.