Chimney flue repair for Bryceville homes
Top tiles replaced from the roof or joints resurfaced with a listed system, sized so your Bryceville fireplace still draws.
- Fully licensed and insured
- Locally owned
- Family owned and operated
- Same-day service
Get Your Free Inspection
Get a quote for chimney and fireplace repair and installation in Jacksonville.
Request received
Thank you. We will call you shortly to set a time.
Quicker by phone? Call (904) 920-5495
Local flue pros for Bryceville chimneys
- Locally owned in Jacksonville
- Family owned and operated
- 100% satisfaction guaranteed
- Free inspection and estimate
- Same-day service available
- 10% off any service
Every flue is measured, so a repair does not shrink it below the size the code sets.
- Free inspection and estimateThe flue at your Bryceville home is swept, examined from both ends and mapped at no charge.
- 100% satisfaction guaranteedIf the repaired flue is not sound and correctly sized when we finish, we make it right.
- Family owned and operatedA family business maps the flue and does the repair, so the plan and the work stay in one set of hands.
A water heater vented through the chimney
Some houses vent a gas furnace or water heater into a masonry flue, sometimes one that once served a fireplace. Gas flue gases carry water vapor, and when they cool on a clay flue the condensate is mildly acidic and wears at the mortar joints.
Joints washed out that way can look sound from the top and open lower down. The code sends gas appliance flue linings to its fuel gas chapter, so the repair has to suit the appliance, not only the tile. Appliance vented into your Bryceville chimney? Call (904) 920-5495 and book a free flue check.
Bryceville is part of Nassau County. The coastline lies beyond Bryceville.
Tile, joint, seal and size
- Cracked and gapped sections coated with a listed resurfacing system
- Seal around the top tile remade
- Relining quoted plainly when repair will not hold
- A written flue plan for your Bryceville chimney, free of charge
How chimney flue repair runs
-
Swept and examined
The flue is cleaned, then looked over from the roof and the firebox with a light and mirrors.
-
Mapped and measured
Each defect is placed by height and wall, and the flue size is checked against what it serves.
-
Repaired by the chosen method
Top tiles swapped from the roof, damaged sections coated with a listed system, or a relining price when repair will not hold.
-
Checked and cured
The finished flue is examined from both ends and left to cure before the first fire.
Before an insert goes into a fireplace in Bryceville
Insert plans bring the flue into focus, since many insert manuals call for a full-height liner.
We check the flue in Bryceville first, so you know whether it can be repaired or should be relined for the insert.
10% off any service booked within 72 hours of inspection
From one cracked tile to a full relining, flue work in Bryceville is discounted.
Replacing the top flue tile from the roof
The top tile is the one flue section that can be reached without taking the chimney apart. When it is cracked or broken, the concrete around it is cut back, the old section lifted out and a new tile set in refractory mortar on the one below.
The new tile has to line up on the inside and stand above the chimney top. Then the seal around it is remade so water sheds rather than soaking in. Repairs lower down cannot be reached this way, which is why top tile replacement suits damage confined to the last section or two.
How we examine a flue without opening it
Nearly all of a flue is out of reach, so it is examined from its ends. From the roof, we look down with a strong light. From the firebox or cleanout, we look up with a light and mirrors. The tiles are counted from the top, so every defect can be placed by height.
Where a stretch of flue cannot be seen from either end, we say so in writing. We do not guess at a section we could not see, and the estimate notes whether more access is needed before that part can be judged. Knowing what was and was not seen is part of an honest flue report.
Using the fireplace before the flue is fixed
A cracked or open-jointed flue lets heat and flue gas reach the masonry around it, and in an interior chimney that masonry sits two inches from framing (R1003.18). That is the reason we ask that a damaged flue not be used until it is repaired.
The repair itself is usually planned around your schedule, with any materials ordered in advance. Until then, the damper stays shut and the fireplace unused. If the flue serves an appliance you rely on, we tell you what that means for the appliance and who should look at it in the meantime.
What goes on the flue map in Bryceville
- Top tiles to replace from the roof, with the seal around them remade
- Flue area measured against the fireplace opening or appliance connector
- Offsets and bends noted with their height and angle
- Sections that could not be seen, and the access they need
Before a flue repair is chosen
How do you see inside a flue?
From both ends, with a strong light and mirrors, after the flue is swept. Anything we could not see is written down as not seen, so nothing is guessed.
When can I light a fire again once the flue is fixed?
After the mortar or resurfacing coat has cured for the time its maker specifies. The estimate gives that time, and we confirm the flue is clear before you light the first fire.
More services in Bryceville
-
-
-
-
-
-
Learn more about chimney flue repairAll services in Bryceville
Seal the flue in your Bryceville chimney
Our satisfaction guarantee covers the flue work we do in Bryceville, tile by tile and joint by joint.
Free Inspection